| 0862 | Construct permanent or temporary steel beam guardrail including placement of steel posts, offset blocks, rail elements, terminal section, delineators, and minor grading around posts and terminal sections. This work code does not cover guiderail installation (cable barrier), which is approved under work code 865. | | | |
| 0865 | Construct cable guiderail including placement of steel posts and placement of guiderail to produce a smooth continuous rail tensioned to the approved manufacturers specification. This work code does not cover guardrail installation (steel beam) which is approved under work code 862. | | | |
| 0900 | Furnish and erect traffic sign systems including overhead signs, exit signs, and wayfinding signs within the right-of-way. Includes installation of break away posts and u-channel posts. Installation of metal poles for overhead signs is approved under work code 1740. | | | |
Shoulder Mounted Sign Structures
| 0902 | Furnish and erect shoulder mounted type A and B sign assemblies within the right of way. Concrete sign foundations approved under work code 825.
| | | |
Overhead Sign Structures
| 0906 | Furnish and erect various types of overhead sign assemblies within right of way. The types of sign assemblies include span structures, cantilever structures and sign structures attached to bridges. Installation of metal poles for overhead signs is approved under work code 1740. Utility Installation/Removal: Power/Electricity is approved under work code 2020.
| | | |
| 1100 | Provide appropriate staffing and equipment to support Safety Service Patrol (SSP) responsibilities in designated coverage areas. These responsibilities include project management, training, safety, staffing, and resource management focused on delivering the following duties: Core Services: quick clearance of minor incidents, emergency traffic control, scene assessment, obstruction and debris removal, agency coordination, and response to other emergency conditions. Secondary Disabled Motorist Assist Services: tire change; fueling, minor maintenance, and phone access.
| Provide contract list with contacts showing history of performing safety service patrol (SSP) services within the last five (5) years (DOT agency contracts are preferred). Minimum of four (4) years of experience providing safety service patrol (SSP) services.
| Must own, rent, or lease (or have the ability to obtain) all vehicles and equipment used to perform SSP duties described. Vehicle fleet must be similar to the current NCDOT SSP, “Incident Management and Assistance Patrol (IMAP)" upon award of a contract. All vehicles, tools, and safety equipment must be in good working order.
| Project Manager and staff members shall have experience staffing, training, equipping, and managing operations for SSP services. Provide a sample detailed training and certification plan for operating SSP services.
|
Work Zone Traffic Control Devices | 1105 | Furnish, install, maintain, relocate, and remove traffic control devices. Perform routine maintenance and inspection of devices while in use. Traffic control devices include, but are not limited to, arrowboards, lighted barrels, attenuator trucks, and MUTCD Type III Barricades. | | | |
| 1110 | Furnish, install, maintain, temporarily cover and uncover, relocate and remove work zone signs as listed on the contract. Applicants should be prepared to install both stationary signs (stay in place) that require the placement of u-channel posts and barricade mounted signs. | | | |
| 1115 | The applicant must be on a tow rotation list with North Carolina State Highway Patrol (NCSHP), a local municipality (e.g. Asheville Police Department), or a bordering state’s highway patrol (e.g. South Carolina Highway Patrol) at the time of prequalification. | Minimum of five (5) years of experience of towing and recovery service | Must own, rent, or lease the primary equipment used for towing and recovery. Each wrecker shall be equipped with legally required lighting and other safety equipment to protect the public and the equipment must be in good working order. | Provide at least three (3) references for which your company has provided tow and recovery services. At least one (1) of the references must be related to a tow rotation list with a state highway patrol or local municipality (e.g. Asheville Police Department). |
Heavy Duty Tow and Recovery | 1120 | The applicant must be on a tow rotation list with North Carolina State Highway Patrol (NCSHP), a local municipality (e.g. Asheville Police Department), or a bordering state’s highway patrol (e.g. South Carolina Highway Patrol) at the time of prequalification. | Minimum of ten (10) years of experience of towing and recovery service, at least five (5) of which include heavy duty tow and recovery experience. | | Provide at least three (3) references for which your company has provided tow and recovery services. At least one (1) of the references must be related to a tow rotation list with a SHP or a local municipality (e.g. Asheville Police Department). |
Symbols, Characters, Markers, Non-Truck Lines | 1204 | Application of pavement marking symbols, characters, markers, and lines. Lines can not exceed 1000 feet per segment. Handliner pavement marking equipment, thermoplastic or paint, shall have a working glass bead dispenser. Must have proper traffic control devices for lane closures or may contract traffic control to a NCDOT approved contractor. | Provide 3 successfully installed marking projects on NC municipal or NCDOT roadways. | | |
| 1206 | Truck application of conventional paint consisting of three elements: pigment, binder, and glass beads. Applicator vehicle must have two 60-gallon minumum capacity paint tanks, glass bead tank with a minimum 500 lb. capacity, and a pressurized bead dispenser. Vehicle should be equipped with spray guns for hand-held paint pavement marking installation of short-line markings, symbols, characters. A handliner with working glass bead dispenser may also be used as needed. | Provide projects list with contacts showing history of performing Paint markings, including three contracts successfully completed in the previous five years (NCDOT roadways preferred). | | |
Pavement Marking- Thermoplastic | 1207 | Truck application of thermoplastic pavement marking materials consisting of four general components: binder, pigment, glass beads, and filler material (usually calcium carbonate, sand, or both). Applicator vehicle must have a 1500 lb. capacity of molten thermoplastic and automatic thermostat controlled. A thermoplastic handliner with working glass bead dispenser will be required for the installation of short-line markings, symbols, characters. | Provide projects list with contacts showing history of Thermoplastic markings, including three contracts successfully completed in the previous five years (NCDOT roadways preferred). | | |
Pavement Marking- Polyurea | 1208 | Truck application of a polyurea based marking material. Contractors performing this work code must list employees who have been certified and trained by the specific polyurea manufacturer to apply their material. List manufacturer(s) of the material you apply. A thermoplastic handliner with working glass bead dispenser will be required for the installation of short-line markings, symbols, characters. | Provide projects list with contacts showing history of performing Polyurea markings, including three contracts successfully completed in the previous five years (NC roadways preferred). | | |
Pavement Marking- Cold Applied | 1209 | Application of preformed tape capable of bonding with the pavement surface. Contractors performing this work code must list the manufacturer tape applicator carts used by the company. | Provide projects list with contacts showing history of performing Cold Applied Plastic Markings, including three contracts successfully completed in the previous five years (NCDOT roadways preferred) | | |
| 1251 | Mobile installation, removal and maintenance of temporary and permanent raised pavement markers. Truck or trailer mounted melters with minimum 1000 lb capacity and automated dispensing system. If installing snowplowable markers, must have the proper groove/slot cutting equipment and plural component mixing device capable of mixing the components in equal parts. Device must have the capacity to hold a minimum of 5 gallons of each component. | Provide projects list with contacts showing history of performing Snowplowable and/or Raised Markers, including 3 contracts successfully completed in the previous five years (NCDOT roadways preferred). | | |
Weigh Station - Weigh-In-Motion | 4510 | Installation, maintenance, and service of Weigh-In Motion (WIM) scales and all necessary equipment at permanent and virtual truck weigh stations.
| | Must have in stock, or the ability to obtain within seventy-two (72) hours, the appropriate parts necessary for maintenance and repairs related to these types of scales.
| Project managers and technicians shall have experience and knowledge with the installation, maintenance, and service (including repairs, calibration, etc.) of weigh-in-motion (WIM) scales at permanent and virtual weigh stations. Previous experience with the Department may be considered.
|
Weigh Station - Transponder Readers | 4520 | Installation, maintenance, and service of Transponder Readers and all necessary equipment at permanent and virtual truck weigh stations. | | Must have in stock, or the ability to obtain within seventy-two (72) hours, the appropriate parts necessary for maintenance and repairs related to this type of equipment.
| Project managers and technicians shall have experience and knowledge with the installation, maintenance, and service (including repairs, calibration, etc.) of transponder readers (such as vehicle classification, over-dimension, queue detection, license plate, USDOT number, tire monitoring, and brake imaging) at permanent and virtual weigh stations. Previous experience with the Department may be considered.
|
Weigh Station - Static Truck Scales
| 4530 | Installation, maintenance, and service of static scales at permanent truck weigh stations.
| | Must have in stock, or the ability to obtain within seventy-two (72) hours, the appropriate parts necessary for maintenance and repairs related to these types of scales.
| Project managers and technicians shall have experience and knowledge in the installation, maintenance, and service (including repairs, calibration, etc.) of static truck scales at permanent weigh stations. Experience in permit required confined spaces is also required. Previous experience with the Department may be considered.
|